Colourless, deeply‐penetrating epoxy agent for repairing concrete surfaces

BAUPOX 100GP is a two‐component, colourless, deeply‐penetrating agent on the basis of epoxy resins.
USE
- Strengthening and sealing of concrete foundations and cement screeds.
- As an anti‐dusting agent for industrial floors subject to intensive activity of external factors.
For professional use only.
PROPERTIES
- Very good penetration
- Very low viscosity
- Easy application
FOUNDATION
Concrete foundation must be stable and of proper carrying capacity for the target static and dynamic loads – concrete of class no less than C20/25 of minimal stripping strength 1,5 N/mm2. The accept‐able humidity of the foundation must not exceed 4% in terms of weight.
The foundation must have a hermetic horizontal insulation protect‐ing it from moisture sucked up through capillary tubes.
Foundations which are to be protected with epoxy layers must be clean and absorbent.
CONDITIONS OF APPLICATION
- Temperature of the foundation– no less than +10°C
- Relative humidity of the air – max. 75%
NOTE: Special attention should be paid that the temperature of the foundation be at least 3°C over the dew point.
Rooms in which the works are performed must be ventilated.
MIXING
BAUPOX® 100 GP is provided in original boxes where the amount of component A (resin) corresponds chemically to the amount of com‐ponent B (hardener). Depending on the final use, the material should be prepared in proper amounts. The indicated weight propor‐tions must be observed at all times.
After adding component B to component A mix it all thoroughly with a slow‐speed mixer (max.400 revolutions per minute) until a ho‐mogenous mixture is achieved (about 3‐5 minutes).
APPLICATION
Apply BAUPOX 100 GP with a roller or brush. Pay attention that no puddles of the preparation be left on the floor.
PROCESSING SUITABILITY
At the temperature of 20°C and at the relative air humidity of 60‐70%, the material remains suitable for use for 25‐30 minutes after mixing.
- Increasing the temperature shortens the setting time of the resin and lowers its viscosity.
- Lowering the temperature prolongs the setting time of the resin and increases its viscosity.
Datasheet: resin for repairing concrete
USABILITY
At the temperature of 20°C and relative air humidity of 60‐70%:
- pedestrian traffic – after 24 hours
- mechanical loads – after 72 hours
- complete resistance – after 7 days
PACKAGING
10 kg, 20 kg
MISCELLANEOUS INFORMATION
All the information contained herein refers to products stored and used in accordance with our recommendations. They have been presented in good faith and take into account the current state of knowledge and experience possessed by Bautech. You are obliged to use the product in accordance with its intended purpose and Bautech’s recommendations. All the technical in‐formation provided herein is based on laboratory tests and trials. Out‐of‐laboratory tests may give different results due to the con‐ditions, location, manner of application and other circumstances that are out of Bautech’s control. Any different recommenda‐tions issued by our employees require a written form, on pain of nullity. These instructions replace all the previous ones and make them void.
In case of adverse humidity and temperature conditions, heaters and/or air driers must be used.
STORAGE
6 months from the date of production specified on the packaging, when stored on pallets in originally closed packaging and at the tem‐perature from +10 to 25°C.
CLEANING
Tools as well as possible stains should be cleaned when still fresh with acetone.
SAFETY MEASURES
BAUPOX® 100 GP is classified as a dangerous material. Guidelines as to the safety of work are included in the specification sheet of dan‐gerous chemical preparations.
TECHNICAL DATA
Product compliant with EN-13813
Mixing proportions
(component A – component B) |
100 : 13 in terms of weight |
Density |
approx. 0,99 g/cm3 |
Consumption | 0,2 - 0,3 kg/m2 |
Colour |
colourless, transparent |
Usability time at |
approx. 25 min. |
Adhesion after 28 days |
over 1,5 N/mm2 (B1,5) |
Application temperature |
from +10°C to +25°C Temperature of the foundation at least 3 °C over the dew point |
|
09 EN 13813 SR-B1,5 |
Summary: concrete, renovation, resin, penetrating, agent, anti dusting, industrial, flooring