Bautech Industrial and Decorative Flooring
Other countries
Polish (Poland)English (United Kingdom)Russian (CIS)
Home page » Industrial » Systems & products » Epoxy resin floors » Polyurethane resin » Baupur 500
Epoxy resin floors

Baupur 500 | Polyurethane varnish

BAUPUR 500 TOP M

Baupur 500 Top M colourless matt varnishColourless polyurethane varnish for finishing layers – matt

 

 

BAUPUR® 500 TOP M is a two‐component, colourless, matt resin based on water polyurethane dispersion.

USE

As a matting finishing layer in industrial and decorative flooring sys‐tems on the basis of dyed quartz aggregate, mineral‐synthetic aggre‐gate and coloured acrylic chips.

For professional use only.

 

FOUNDATION

The surfaces to be protected with a layer of BAUPUR® 500 TOP M must be clean and free from substances decreasing adhesion. BAUPUR® 500 TOP M should be applied on the floor within 48 hours from making the last system layer. If the required period is not be observed, the surface must be thoroughly ground and all dust must be removed from it.

CONDITIONS OF APPLICATION

  • Temperature of the foundation – no less than +10°C
  • Relative humidity of the air – max. 75%

NOTE: Special attention should be paid that the temperature of the foundation be at least 3°C over the dew point temperature. Rooms in which the works are performed must be ventilated.

How to mix

BAUPOX® 500 TOP M is provided in original boxes where the amount of component A (resin) corresponds chemically to the amount of component B (hardener). Depending on the final use, the material should be prepared in proper amounts, unconditionally observing the indicated weight proportion.

After adding component B to component A mix it all thoroughly with a slow‐speed mixer (max. 400 revolutions per minute) until a ho‐mogenous mixture is achieved (about 3‐5 minutes).

PROCESSING SUITABILITY

At the temperature of 20°C and at the relative air humidity of 60‐70%, the material remains suitable for use for 25‐30 minutes after mixing.

  • Increasing the temperature shortens the setting time of the resin and lowers its viscosity.
  • Lowering the temperature prolongs the setting time of the resin and increases its viscosity.

USABILITY

At the temperature of 20°C and relative air humidity of 60‐70%:

  • pedestrian traffic – after 24 hours
  • mechanical loads – after 72 hours
  • complete resistance – after 7 days

MISCELLANEOUS INFORMATION

All the information contained herein refers to products stored and used in accordance with our recommendations. They have been presented in good faith and take into account the current state of knowledge and experience possessed by Bautech. You are obliged to use the product in accordance with its intended purpose and Bautech’s recommendations. All the technical in‐formation provided herein is based on laboratory tests and trials. Out‐of‐laboratory tests may give different results due to the con‐ditions, location, manner of application and other circumstances that are out of Bautech’s control. Any different recommenda‐tions issued by our employees require a written form, on pain of nullity. These instructions replace all the previous ones and make them void.

In case of adverse humidity and temperature conditions, heaters and/or air driers must be used.

Polyurethane varnish for epoxy flooring - Technical sheet pdf

 

 

EXAMPLES OF USE

Finish layer ‐ matt

Apply BAUPOX® 500 TOP M in an even manner on the foundation with a varnish roller. Roll the material out in two perpendicular directions to achieve a uniform surface. In case of larger works change the roller every 30 minutes.

Consumption: 0,10 - 0,15 kg/m2

NOTE:

Contact of newly made surfaces with moisture (rain, dew, high humidity of the air) will disturb the setting process. The surface may remain sticky for a longer period of time and have a tendency to develop milk‐like pigmentation.

PACKAGING

2,5 kg, 5kg, 10 kg,

STORAGE

6 months from the date of production specified on the packaging, when stored on pallets in originally closed packaging and at the tem‐perature from +10 to 25°C.

CLEANING

Tools as well as possible stains should be cleaned when still fresh with water.

SAFETY MEASURES

BAUPUR® 500 TOP M is classified as a dangerous material. Guidelines as to the safety of work are included in the specification sheet of dangerous chemical preparations.

TECHNICAL DATA

Product compliant with EN-13813

Mixing proportions

(compo‐nent A – component B)

100 : 19  in terms of weight

Density

approx. 1,0 g/cm3

Colour

colourless, transparent

Usability time at
temp. +20°C

approx. 25 min.

Adhesion after 28 days

over 1,5 N/mm2(B1,5)

Application temperature

from +10°C to +25°C

Temperature of the foundation at least 3 °C over the dew point

CE

09

EN 13813

SR-B1,5

 

Tags: polyurethane, varnish, resin, epoxy, flooring, finishing, layer, matt

  OUR CLIENTS

  • logos_01-07.jpg
  • logos_02-06.jpg
  • logos_03.jpg
  • logos_04-05.jpg
  • logos_04.jpg
  • logos_05.jpg
  • logos_06.jpg
  • logos_11.jpg
  • logos_12.jpg
  • logos_17.jpg
  • logos_19-19.jpg
  • logos_19-23.jpg
  • logos_19-24.jpg
  • logos_19.jpg
  • logos_21.jpg
  • logos_22.jpg
  • logos_26.jpg
  • logos_27-32.jpg
  • logos_27.jpg
  • logos_29-34.jpg
  • logos_29.jpg
  • logos_30.jpg
  • logos_36.jpg
  • logos_38.jpg
  • logos_39-43.jpg
  • logos_39.jpg
  • logos_40.jpg
  • logos_42.jpg

Call Phone +48 22 716 77 91

Contact details

© 2019 All right reserved. BAUTECH sp. z o.o. ul. Staszica 25, 05-500 Piaseczno k. Warszawy tel. 22 716-77-91, fax 22 716-77-90, NIP 522-000-09-96, Regon: 012547108, KRS nr 0000166495 Sąd Rejonowy dla m.st. Warszawy, XIV Wydział Gospodarczy KRS, share capital: 51 000 PLN, bank account PKO BP S.A. 57 1020 1068 0000 1502 0146 4957

project by: Intermedium.pl interactive agency