Bautech Industrial and Decorative Flooring
Other countries
Polish (Poland)English (United Kingdom)Russian (CIS)
Home page » Industrial » Systems & products » Epoxy resin floors » Epoxy resin » Baupox 400
Epoxy resin floors

Baupox 400 | Finishing & binding resin

BAUPOX® 400 colourless resin

Colourless epoxy resin with a wide range of applica‐tions

Baupox 400 colourless finishing resin



BAUPOX® 400 is a two‐component, transparent epoxy resin based on bisfenol A/F with no solvents added.


  • As a binding agent in industrial and decorative floors on the basis of dyed quartz aggregate and mineral‐synthetic aggregate.
  • For the making of finishing layers in industrial and decorative systems on the basis of colour polymer chips and dyed quartz ag‐gregate.

For professional use only.



Concrete foundation must be stable and of proper carrying capacity for the target static and dynamic loads – concrete of class no less than C20/25 of minimal stripping strength 1,5 N/mm2. The accept‐able humidity of the foundation cannot exceed 4% in terms of weight.

The foundation must have a hermetic horizontal insulation protect‐ing it from moisture sucked up through capillary tubes.

Foundations which are to be protected with epoxy layers must be clean and absorbent. Cement wash, dirt of all kinds and old protec‐tion layers should be removed mechanically by grinding, shot blasting or milling. When renovating old epoxy floors, their adherence to the foundation must be absolutely checked (no less than 1.5 N/mm2) and the surface degreased and tarnished mechanically.



  • Temperature of the foundation – no less than +10°C
  • Relative humidity of the air – max. 75%

NOTE: Special attention should be paid that the temperature of the foundation be at least 3°C over the dew point temperature. Rooms in which the works are performed must be ventilated.


BAUPOX® 400 is provided in original boxes where the amount of component A (resin) corresponds chemically to the amount of com‐ponent B (hardener). Depending on the final use, the material should be prepared in proper amounts, unconditionally observing the indicated weight proportion.

After adding component B to component A mix it all thoroughly with a slow‐speed mixer (max.400 revolutions per minute) until a ho‐mogenous mixture is achieved (about 3‐5 minutes). In case of pre‐paring repair, levelling or base mortars, mineral filler should be added to the resin during mixing in the amount appropriate for the given use.


At the temperature of 20°C and at the relative air humidity of 60‐70%, the material remains suitable for use for 25‐30 minutes after mixing.

  • Increasing the temperature shortens the setting time of the resin and lowers its viscosity.
  • Lowering the temperature prolongs the setting time of the resin and increases its viscosity.


At the temperature of 20°C and relative air humidity of 60‐70%:

  • pedestrian traffic – after 24 hours
  • mechanical loads – after 72 hours
  • complete resistance – after 7 days


All the information contained herein refers to products stored and used in accordance with our recommendations. They have been presented in good faith and take into account the current state of knowledge and experience possessed by Bautech. You are obliged to use the product in accordance with its intended purpose and Bautech’s recommendations. All the technical in‐formation provided herein is based on laboratory tests and trials. Out‐of‐laboratory tests may give different results due to the con‐ditions, location, manner of application and other circumstances that are out of Bautech’s control. Any different recommenda‐tions issued by our employees require a written form, on pain of nullity. These instructions replace all the previous ones and make them void.

In case of adverse humidity and temperature conditions, heaters and/or air driers must be used.

Finishing epoxy resin - Technical sheet pdf




Finishing layer


Spread the material evenly in one or two layers using a rubber squeegee and then roll out to obtain a uniform surface.

Consumption: 0,25-0,50 kg/m2


Spread the material evenly in one or two layers using a rubber squeegee and then roll out to obtain a uniform surface.

Consumption: 0,50-0,75 kg/m2



Spread the material evenly in one layer using a rubber squeegee or a steel long float and then roll out to obtain a uniform surface.

Consumption: 0,20 kg/m2


NOTE: Contact of newly made surfaces with moisture (rain, dew, high humidity of the air) will disturb the setting process. The surface may remain sticky for a longer period of time and have a tendency to develop milk‐like pigmentation.



10 kg, 20 kg


6 months from the date of production specified on the packaging, when stored on pallets in originally closed packaging and at the tem‐perature from +10 to 25°C.


Tools as well as possible stains should be cleaned when still fresh with acetone.


BAUPOX® 400 is classified as a dangerous material. Guidelines as to the safety of work are included in the specification sheet of danger‐ous chemical preparations.


Epoxy resin compliant with EN-13813

Mixing proportions

(component A – component B)

100 : 45 in terms of weight


approx. 1,1 g/cm3


colourless, transparent

Usability time at
+20°C - 100g

approx. 25 min.

Adhesion after 28 days

over 1,5 N/mm2 (B1,5)

Application temperature

from +10°C to +30°C

Temperature of the foundation at least 3°C over the dew point



EN 13813



Tags, epoxy, resin, finishing, layer, binding, agent, industrial, flooring


  • logos_01-07.jpg
  • logos_02-06.jpg
  • logos_03.jpg
  • logos_04-05.jpg
  • logos_04.jpg
  • logos_05.jpg
  • logos_06.jpg
  • logos_11.jpg
  • logos_12.jpg
  • logos_17.jpg
  • logos_19-19.jpg
  • logos_19-23.jpg
  • logos_19-24.jpg
  • logos_19.jpg
  • logos_21.jpg
  • logos_22.jpg
  • logos_26.jpg
  • logos_27-32.jpg
  • logos_27.jpg
  • logos_29-34.jpg
  • logos_29.jpg
  • logos_30.jpg
  • logos_36.jpg
  • logos_38.jpg
  • logos_39-43.jpg
  • logos_39.jpg
  • logos_40.jpg
  • logos_42.jpg

Call Phone +48 22 716 77 91

Contact details

© 2021 All right reserved. BAUTECH sp. z o.o. ul. Staszica 25, 05-500 Piaseczno k. Warszawy tel. 22 716-77-91, fax 22 716-77-90, NIP 522-000-09-96, Regon: 012547108, KRS nr 0000166495 Sąd Rejonowy dla Warszawy, XIV Wydział Gospodarczy KRS, share capital: 51 000 PLN, bank account PKO BP S.A. 57 1020 1068 0000 1502 0146 4957

project by: interactive agency