Bautech Industrial and Decorative Flooring
Other countries
Polish (Poland)English (United Kingdom)Russian (CIS)
Home page » Industrial » Systems & products » Epoxy resin floors » Epoxy resin » Baupox 100 ST
Epoxy resin floors

Baupox 100ST | Universal epoxy resin

BAUPOX® 100 ST epoxy resin

Żywica epoksydowa Baupox 100 ST  

Universal, colourless epoxy resin for technical applications 

  

BAUPOX® 100 ST is a two‐component, transparent epoxy resin based on bisfenol A/F with no solvents added.

USE

  • Impregnation and grounding of seasoned/stabilized concrete foundations and cement screeds.
  • Making levelling layers and polymer screeds.
  • Making base layers in systems with granulate from natural or dyed quartz aggregate.
  • Anchoring of elements in various types of founda‐tions/bases/substrates.

CAUTION:  do not use for finishing layers.

For professional use only.

 

FOUNDATION

Concrete foundation must be stable and of proper carrying capacity for the target static and dynamic loads – concrete of class no less than C20/25 of minimal stripping strength 1,5 N/mm2. The accept‐able humidity of the foundation cannot exceed 4% in terms of weight.

The foundation must have a hermetic horizontal insulation protect‐ing it from moisture sucked up through capillary tubes.

Foundations which are to be protected with epoxy layers must be clean and absorbent. Cement wash, dirt of all kinds and old protec‐tion layers should be removed mechanically by grinding, shot blasting or milling. When renovating old epoxy floors, their adherence to the foundation must be absolutely checked (no less than 1.5 N/mm2) and the surface degreased and tarnished mechanically.

CONDITIONS OF APPLICATION

- Temperature of the foundation – no less than +10°C

- Relative humidity of the air – max. 75%

NOTE: Special attention should be paid that the temperature of the foundation be at least 3°C over the dew point temperature. Rooms in which the works are performed must be ventilated.

MIXING

BAUPOX® 100 ST is provided in original boxes where the amount of component A (resin) corresponds chemically to the amount of com‐ponent B (hardener). Depending on the final use, the material should be prepared in proper amounts, unconditionally observing the indicated weight proportion.

After adding component B to component A mix it all thoroughly with a slow‐speed mixer (max.400 revolutions per minute) until a ho‐mogenous mixture is achieved (about 3‐5 minutes). In case of pre‐paring repair, levelling or base mortars, mineral filler should be added to the resin during mixing in the amount appropriate for the given use.

PROCESSING SUITABILITY

At the temperature of 20°C and at the relative air humidity of 60‐70%, the material remains suitable for use for 25‐30 minutes after mixing.

  • Increasing the temperature shortens the setting time of the resin and lowers its viscosity.
  • Lowering the temperature prolongs the setting time of the resin and increases its viscosity.
USABILITY

At the temperature of 20°C and relative air humidity of 60‐70%:

  • pedestrian traffic – after 24 hours
  • mechanical loads – after 72 hours
  • complete resistance – after 7 days
MISCELLANEOUS INFORMATION

All the information contained herein refers to products stored and used in accordance with our recommendations. They have been presented in good faith and take into account the current state of knowledge and experience possessed by Bautech. You are obliged to use the product in accordance with its intended purpose and Bautech’s recommendations. All the technical in‐formation provided herein is based on laboratory tests and trials. Out‐of‐laboratory tests may give different results due to the con‐ditions, location, manner of application and other circumstances that are out of Bautech’s control. Any different recommenda‐tions issued by our employees require a written form, on pain of nullity. These instructions replace all the previous ones and make them void.

In case of adverse humidity and temperature conditions, heaters and/or air driers must be used.

Grounding epoxy resin - Technical sheet pdf

 

EXAMPLES OF USE

Grounding layer

BAUPOX® 100 ST should be applied on the foundation in one or two layers using a rubber squeegee and then a roller, until the effect of even and complete saturation is achieved.

Depending on the kind of the target floor solution, the fresh surface may be left smooth or sprinkled over with fractional quartz aggregate in the amount of 0.5‐1.5 kg/m2.

Consumption: 0,30-0,50 kg/m2 - depending on the absorptivity and class of the foundation.

Base layer in systems with granulate from quartz aggregate

Apply BAUPOX® 100 ST filled in the proportion of 1:1 with quartz aggregate fraction 0.2‐0.8 mm evenly on the foundation using a long steel float, leaving on its surface a uniform layer filling the pores and levelling slight irregularities in the surface. Sprinkle the surface over, completely and evenly, depending on the target flooring solution, with natural or dyed quartz aggregate of proper fraction (about 3.0 kg/m2).

When it hardens, sweep the excessive amount of the aggregate, delicately regrind the surface with abrasive paper and then remove dust from the whole of it.

Consumption: 0,60 kg/m2

Epoxy screeds

Apply BAUPOX® 100 ST filled in the proportion of 1:5 to 1:10, de‐pending on the fraction of the aggregate used, evenly on grounded foundation with a long steel float, then float it manually or mechani‐cally until a uniform surface is obtained.

Consumption of the mixture per 1 mm of the layer: about 1.8 kg

 

NOTE: Contact of newly made surfaces with moisture (rain, dew, high humidity of the air) will disturb the setting process. The surface may remain sticky for a longer period of time and have a tendency to develop milk‐like pigmentation.

 

CLEANING

Tools as well as possible stains should be cleaned when still fresh with acetone.

SAFETY MEASURES

BAUPOX® 100 ST is classified as a dangerous material. Guidelines as to the safety of work are included in the specification sheet of dan‐gerous chemical preparations.

PACKAGING

10 kg, 20 kg

 

STORAGE

6 months from the date of production specified on the packaging, when stored on pallets in originally closed packaging and at the tem‐perature from +10 to 25°C.

 

TECHNICAL DATA

Product compliant with EN-13813

Mixing proportions

(compo‐nent A – component B)

as given on packaging label

Density

approx. 1,1 g/cm3

Colour

colourless, transparent

Usability time at
+20°C - 100g

approx. 25 min.

Adhesion after 28 days

over 1,5 N/mm2 (B1,5)

Application temperature

from +10°C to +25°C

Temperature of the foundation at least 3 °C over the dew point

CE

 

09

EN 13813

SR-B1,5

 

Tags: epoxy resin, colourless, transparent, grounding, impregnation, flooring

  OUR CLIENTS

  • logos_01-07.jpg
  • logos_02-06.jpg
  • logos_03.jpg
  • logos_04-05.jpg
  • logos_04.jpg
  • logos_05.jpg
  • logos_06.jpg
  • logos_11.jpg
  • logos_12.jpg
  • logos_17.jpg
  • logos_19-19.jpg
  • logos_19-23.jpg
  • logos_19-24.jpg
  • logos_19.jpg
  • logos_21.jpg
  • logos_22.jpg
  • logos_26.jpg
  • logos_27-32.jpg
  • logos_27.jpg
  • logos_29-34.jpg
  • logos_29.jpg
  • logos_30.jpg
  • logos_36.jpg
  • logos_38.jpg
  • logos_39-43.jpg
  • logos_39.jpg
  • logos_40.jpg
  • logos_42.jpg

Call Phone +48 22 716 77 91

Contact details

© 2019 All right reserved. BAUTECH sp. z o.o. ul. Staszica 25, 05-500 Piaseczno k. Warszawy tel. 22 716-77-91, fax 22 716-77-90, NIP 522-000-09-96, Regon: 012547108, KRS nr 0000166495 Sąd Rejonowy dla m.st. Warszawy, XIV Wydział Gospodarczy KRS, share capital: 51 000 PLN, bank account PKO BP S.A. 57 1020 1068 0000 1502 0146 4957

project by: Intermedium.pl interactive agency