Bautech Industrial and Decorative Flooring
Other countries
Polish (Poland)English (United Kingdom)Russian (CIS)
Home page » Industrial » Systems & products » Hardened concrete floors » Floor hardeners » Multitop Enduro
Hardened concrete floors

Multitop Enduro Hardener

MULTITOP ENDURO is a metallic-siliceous, ready to use, dry shake topping for monolithic concrete floors. When sprinkled and trowelled into fresh wet concrete floors, it forms a wear resistant smooth surface. Provides increased resistance to the penetration of oils, grease, etc. and is easily cleaned. MULTITOP ENDURO is a dry powder comprising hard aggregates, cements and compatible admixtures.



MULTITOP ENDURO is used for high specification floors with better abrasion resistance, provides a hard wearing surface for use in factories, warehouses, workshops etc.

For professional use only.


special properties

  • Guaranteed wear resistance
  • Cost effective
  • Sealed and dust-proofed
  • Fast track

method of use

To ensure a high standard of floor contractor should operate in as clean and protected an environment as possible. Every effort should be made to ensure even application of MULTITOP ENDURO and correct timing and trowelling techniques are essential. The concrete deliveries should be of consistent quality. A concrete slump in the range 80 to 100 mm will normally give best results. The slab should be of good quality concrete with a water/cement ratio < 0.5, aggregate size should be <= 16 mm, cement content <=350kg MULTITOP ENDURO is applied evenly in two separate applications of 2,5 kg/m2 each, the first stage is applied after the surface bleed water has either been removed or evaporated. Care should be taken when applying by hand not to cast the material over long distances as this will reduce the consistency of the finished surface. The first application should be worked into the slab followed immediately with the sprinkling on of the second measurement. MULTITOP ENDURO results in the slab surface becoming stiff more quickly than usual. Careful trimming should take place along the edges where adjoining slabs are to be poured. Final finishing to close pores and remove undulations can be achieved either by hand or powered trowel. To achieve the most satisfying results it is essential that best powerfloating practice be followed. Excessive powerfloating can cause blemishes. Cure and seal MULTITOP ENDURO immediately after finishing using BAUSEAL ENDURO. Apply BAUSEAL ENDURO by roller or fine mist spray. Disperse by roller any pools which form. After completing the saw cuts clean off any residual lubricant slurry without delay. To maintain the most pleasing finish for hand-over protect the surface during subsequent site operations and clean carefully.


technical data
Packaging: 30 kg bags.
Dosage: approx. 5 kg/m2
Colour Range: MT 300 - steel grey,
MT 301 - brick red,
MT 302 - olive green,
MT 303 - platinum grey,
MT 304 - titanum grey,
MT 305 - graphite
Compressive strength: > 50 N/mm2
Bending strength: > 10 N/mm2
Storage: 6 months when stored in cool dry conditions in original, unopened containers.


  • logos_01-07.jpg
  • logos_02-06.jpg
  • logos_03.jpg
  • logos_04-05.jpg
  • logos_04.jpg
  • logos_05.jpg
  • logos_06.jpg
  • logos_11.jpg
  • logos_12.jpg
  • logos_17.jpg
  • logos_19-19.jpg
  • logos_19-23.jpg
  • logos_19-24.jpg
  • logos_19.jpg
  • logos_21.jpg
  • logos_22.jpg
  • logos_26.jpg
  • logos_27-32.jpg
  • logos_27.jpg
  • logos_29-34.jpg
  • logos_29.jpg
  • logos_30.jpg
  • logos_36.jpg
  • logos_38.jpg
  • logos_39-43.jpg
  • logos_39.jpg
  • logos_40.jpg
  • logos_42.jpg

Call Phone +48 22 716 77 91

Contact details

© 2020 All right reserved. BAUTECH sp. z o.o. ul. Staszica 25, 05-500 Piaseczno k. Warszawy tel. 22 716-77-91, fax 22 716-77-90, NIP 522-000-09-96, Regon: 012547108, KRS nr 0000166495 Sąd Rejonowy dla Warszawy, XIV Wydział Gospodarczy KRS, share capital: 51 000 PLN, bank account PKO BP S.A. 57 1020 1068 0000 1502 0146 4957

project by: interactive agency